Strict Standards: Non-static method phpbb_feed_factory::init() should not be called statically in /home/bridgec/src.bridgecitytools.com/magento/discussion/feed.php on line 66
[phpBB Debug] PHP Notice: in file /feed.php on line 171: Cannot modify header information - headers already sent by (output started at /feed.php:66)
[phpBB Debug] PHP Notice: in file /feed.php on line 172: Cannot modify header information - headers already sent by (output started at /feed.php:66)
BridgeCityTools.com Serving Woodworkers Worldwide for a Quarter Century! 2018-08-08T22:59:58-07:00 https://www.bridgecitytools.com/discussion/feed.php?f=30 2018-08-08T22:59:58-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=281&p=1829#p1829 <![CDATA[General Uses • Re: Mortise techniques]]> Assignment Writing Australia part referred to as a rail, fits into a square or rectangular hole cut into the corresponding part.

Statistics: Posted by jerryjames086@gmail.com — Wed Aug 08, 2018 10:59 pm


]]>
2018-08-06T01:04:05-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=250&p=1827#p1827 <![CDATA[General Uses • Re: Any reason to use tenonmake with hand tools only?]]> custom assignment help seat with the found in the primary cut and the Tenonmaker amongst them, and after that flip the Tenonmaker and place the saw against it and make your second cut.

Statistics: Posted by saracraw1992@gmail.com — Mon Aug 06, 2018 1:04 am


]]>
2018-07-17T22:03:35-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=250&p=1811#p1811 <![CDATA[General Uses • Re: Any reason to use tenonmake with hand tools only?]]> bestessay reviews is done for the approval or the humans. The depth of the discussion is highlighted for the use in various fields for the students.

Statistics: Posted by hunterarida@jourrapide.com — Tue Jul 17, 2018 10:03 pm


]]>
2015-01-29T12:57:02-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=470&p=1569#p1569 <![CDATA[General Uses • Re: TM-1 "Tab"?]]>
The "Tab" on the end of the TM-1 is crucial for the tool to be used as a flip stop. It keeps the tool parallel to the fence or reference. You do not use it when measuring a mortise or female gap, but you do need it when it is time for cutting.

Best-

John

Statistics: Posted by John@bridgecitytools.com — Thu Jan 29, 2015 12:57 pm


]]>
2015-01-28T23:04:27-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=470&p=1568#p1568 <![CDATA[General Uses • TM-1 "Tab"?]]>
Thanks,
Duane

Statistics: Posted by cj8jeepr@yahoo.com — Wed Jan 28, 2015 11:04 pm


]]>
2011-09-04T16:10:41-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=281&p=1071#p1071 <![CDATA[General Uses • Mortise techniques]]>
As I am looking for any excuse to test the Tenonmaker's abilities, I am curious as to the methods used to create the mortises for the Tenonmaker video.

I am in the process of constructing a workbench that requires several large M&T joints (both stopped and through tenons, 1.5 x 2.25" and 1 x 3", respectively) in beech stock 3-3.5" in cross section. I've tried a plunge router technique thus far, with less than satisfying results and the noise only underscores my dissatisfaction. The cut seems quite uncontrolled even with a fence or template, although perhaps it's my lack of experience. Using a drill press followed by chiseling seems calmer, but not sure if the results will be better.

Thanks for any suggestions! And thanks for designing all these great ways to keep me entertained in my free time.

Randy

Statistics: Posted by rotto@mac.com — Sun Sep 04, 2011 4:10 pm


]]>
2011-03-10T12:33:06-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=254&p=1003#p1003 <![CDATA[General Uses • ]]>
-John

Statistics: Posted by John — Thu Mar 10, 2011 12:33 pm


]]>