Strict Standards: Non-static method phpbb_feed_factory::init() should not be called statically in /home/bridgec/src.bridgecitytools.com/magento/discussion/feed.php on line 66
[phpBB Debug] PHP Notice: in file /feed.php on line 171: Cannot modify header information - headers already sent by (output started at /feed.php:66)
[phpBB Debug] PHP Notice: in file /feed.php on line 172: Cannot modify header information - headers already sent by (output started at /feed.php:66)
BridgeCityTools.com Serving Woodworkers Worldwide for a Quarter Century! 2014-04-19T10:44:50-07:00 https://www.bridgecitytools.com/discussion/feed.php?f=23 2014-04-19T10:44:50-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=248&p=1490#p1490 <![CDATA[Jointmaker SW • Re: Cuts Not Straight in Wider Stock]]>
It looks like the email thread that you posted was cut off before solutions were discussed. If you still have it and could re-post it that would be great.
Thanks,
Dave

Statistics: Posted by dave@wiseriverforestry.com — Sat Apr 19, 2014 10:44 am


]]>
2014-04-19T10:08:56-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=439&p=1489#p1489 <![CDATA[Jointmaker SW • Re: difficulty lowering blade and not cutting straight]]>
I think I have them in the right place as they are inserted on the back side of the screw in between the grey guide and where the guide fastens to the spine. As I understand from the manual, two shim washer go between each guide (black and gray) at the front end (blade lifting handle side) only of the JM. I assume there are no shim washers on the opposite side? Perhaps I do need a thicker shim as you suggest. Any other ideas out there?

Thanks,
Dave

Statistics: Posted by dave@wiseriverforestry.com — Sat Apr 19, 2014 10:08 am


]]>
2014-04-19T04:49:03-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=439&p=1488#p1488 <![CDATA[Jointmaker SW • Re: difficulty lowering blade and not cutting straight]]>
I think both of your problems may be related to the shim washers that go between the grey guide and the black upright mounting bracket. Maybe double check that they are between the grey piece and the black piece and not between the screw head and the black upright. If they're in the proper location, you may need a slightly fatter shim washer. Bridge City supplied me with a couple thicker ones a few years ago- can't remember the specs off hand.

Best,
Rutager

Statistics: Posted by rwest — Sat Apr 19, 2014 4:49 am


]]>
2014-04-18T21:02:14-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=439&p=1487#p1487 <![CDATA[Jointmaker SW • difficulty lowering blade and not cutting straight]]> I'm also getting some significant blade deflection when cutting stock over 1" thick, even light wood such as wester red cedar. Not sure if these two problems are related, but help with either would be very much appreciated.

Thanks
Dave

Statistics: Posted by dave@wiseriverforestry.com — Fri Apr 18, 2014 9:02 pm


]]>
2012-09-19T15:22:28-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=357&p=1295#p1295 <![CDATA[Jointmaker SW • Re: Use of SW by person with Limited LEFT ARM/Hand strength?]]>
I can't answer your question directly, I would certainly be happy to let you, or a friend try any of my tools if you happen to be in the metro area of MN. Another option might be to attend one of the Wood Working in America events and try out some of the Bridge City Tools.

Best,
Rutager

Statistics: Posted by rwest — Wed Sep 19, 2012 3:22 pm


]]>
2012-09-18T09:09:01-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=357&p=1293#p1293 <![CDATA[Jointmaker SW • Use of SW by person with Limited LEFT ARM/Hand strength?]]>
drj@crewonward.com wallace.l.johnston@gmail.com

Statistics: Posted by wallace.l.johnston@gmail.com — Tue Sep 18, 2012 9:09 am


]]>
2012-01-12T01:58:45-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=150&p=1170#p1170 <![CDATA[Jointmaker SW • Re: Fixed table vs sliding.]]> Statistics: Posted by brandonpeterson789@gmail.com — Thu Jan 12, 2012 1:58 am


]]>
2011-02-14T17:13:15-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=248&p=973#p973 <![CDATA[Jointmaker SW • Cuts Not Straight in Wider Stock]]>
"I purchased, assembled, and have been using the JM-SW for about 2 weeks. Yesterday in attempting to make a 45 degree miter cut in 1/2" thick x 3 " wide stock I ended up with the cut not coming out square. The fence is square to the blade, the blade tracks properly and I get square crosscuts...I even get square miter cuts in material that is not as wide (like 1" wide). Please tell me what I might need to do to correct this."
-John West

[b]John:

I am assuming you are using the standard blade which has 28 teeth per inch. With a 3â€

Statistics: Posted by John — Mon Feb 14, 2011 5:13 pm


]]>
2010-02-05T08:22:09-07:00 https://www.bridgecitytools.com/discussion/viewtopic.php?t=176&p=717#p717 <![CDATA[Jointmaker SW • JMP-sw Threaded holes in Tabletops]]>
Just a mention about the threaded holes in the new table tops for the JMP-v2, -SW & Upgrade kits. ...

They are going to be 10/32" verses the 8/32" on the JMP-v1, this is a good thing.

The purpose of these threaded holes is - in order to attach jigs and to ease in work holding methods as you see fit down the line.

(I don't believe I mentioned this earlier, I actually just noticed this yesterday when I had the v1 & v2 versions next to each other.)

At some point Michael will inform me as to the "class" of the 10/32" thread.
Within the Imperial system you have coarse and fine threads -within each of those divisions you have classes.
The class of the thread in combination with the threaded machine screws will determine whether your fit is tight or a little wiggly.

-Roger

Statistics: Posted by savatteridesigns — Fri Feb 05, 2010 8:22 am


]]>