How to Make the Fog of War Board in Pictures…

Last April I taught two classes at the Marc Adams School of Woodworking on how to make my “Fog of War”, which is a metaphorical sculpture posing as a chess set.

There was not enough time in the week to make both the players and the board and I promised to make this post available for those who wanted to complete the piece. So here ya go!



Although these images are focused on the lattice work, the bones of the board were made exactly the same way, the sticks were bigger (thickness of 0.150″ and a width of 1.375″.)

In the image below you can see the simple jig for thickness planing the lattice strips. I used the HP-8 plane with depth skids to dimension the sticks from 0.060″+ to a precise 0.050″. The accuracy of using depth skids is off the charts – all 240 sticks were within 0.001″ of 0.050″ in thickness. As you will see, this accuracy is paramount to making gap free joints. To set the skids to the correct depth, I set the plane body on gage pins, dropped the skids and tightened. I am a big fan of gage pins in woodworking and you will see later that I used them in a couple of applications in this project. I used a similar set-up to dimension the sticks to their exact width of 0.220″ and was able to do 4 at a time.

IMG_0026

After all 240 sticks were properly sized, I pre-finished them by dragging all edges over a rag loaded with wax.

IMG_0367


Here’s a pile of waxed sticks drying.IMG_0368


It took a while to buff all of these out by hand, but they were baby butt smooth when done. Here’s a fistful of pieces and you can see the precision that is possible using depth skids…
IMG_0370


Next, I created bundles to gang cut the half-lap joints using Scotch tape – and trimmed one end for reference using the Jointmaker Pro as you can see here. The cuts were all single pass.

IMG_0372


Using the KM-1 Kerfmaker against the JMP Precision Fence the half-laps were cut in 3 passes per joint. I cut one joint in each of the bundles before I made a fence move. I literally could not feel the saw cutting when I made these single pass cuts.


IMG_0373



I made a test cut and checked the accuracy using a 0.049″ diameter gage pin which would make for a 0.001″ interference fit between members. Here the gage pin fits perfectly. When you are working at such a small scale, seeing and measuring becomes tedious. It is easy to quantify slots and grooves with gage pins.
IMG_0383


With all the joints cut, it is easy to see the accuracy, and all of this was done by hand. The “grids” of the lattice work were 0.150″ square and the math is straight forward, the fence stop needed to be moved 0.200″ between cuts (the desired opening plus one stick width).
IMG_0375


Here’s what the finished and waxed pieces look like when complete…
IMG_0381


Now the fun part; assembly. All of these joints went together with just a tiny bit of finger pressure. If your stock width varies, you will either have gaps (anybody can make joints with gaps) OR, if it is too tight, the sticks will yield and curl, or break. All of the precision touted in this post is absolutely necessary. There is no glue used in the grid assemblies.
IMG_0382


IMG_0380


Here you can see the KM-1 and the piece of wood I used to calibrate to the blade in the JMP…
IMG_0384


I made this project more stressful than I had planned. I did not make enough extra sticks so I had little room for screw-ups. Unfortunately, I am really good at screwing up..
IMG_0378


It is now time to cut the lattice to fit the openings in the big board. To be safe, each and every lattice was measured and fitted one at a time. I started by double stick taping a backing board to each grid assembly. This served as a clamp pad and kept the sticks from bending during the four cuts. No two grids are orientated the same.
IMG_0396


IMG_0394


Here’s what it looks like on the JMP…
IMG_0388


The complete clamping set-up on the JMP. On the falloff side of the saw, there is double stick tape on the table and on the underside of the clamp pad. This keeps these thin pieces of wood from bending during the cut. There is too much work in each of these to lose them at this step.
IMG_0397


You can see how well the tape holds here…
IMG_0399


Hand fitting these was a breeze. The very first thing I did was add a wood block to one of the Precision Fence fingers for a larger reference surface (you can see it in the pic above). I then set the stop up to cut 1.750″ and set the dial on the fence to ‘0″. Next, I opened my digital calipers to 1.750″ and then “zeroed” the caliper. This means when the caliper was closed it read -1.750″. Last, I measured the width of an opening and the caliper read 0.001″. Now all I needed to do was set the dial on the fence to +0.001″. It was that easy. Here is a pic of the caliper and the dial…
IMG_0400


Here is a finished cut grid…
IMG_0386


Each grid in the board needed a stop for the lattice. These were measured and cut using the technique above and glued in place. I used a double square with the blade protruding .2200″ for flushing the tops of the lattice with the top of the “bones” which defined the board.
IMG_0387


Here the grid is ready to be seated. They are retained with a tiny amount of glue on each end of the four anchor sticks. Each grid required a gentle tap home. The butt joints, all at odd angles, are light tight.
IMG_0389


This was tense because I had almost no room for error, which was an error in itself. Here are all the remaining pieces after final assembly.
IMG_0403


The top was hand sanded with a sanding block and finished with wax. Here is the almost finished board…
IMG_0406


Here’s a close up of the cross lap joints, they are almost invisible…
IMG_0405



This aspect of the project took 7 board feet of eastern hard rock maple and 47 hours. It was really fun because I didn’t screw up (thank goodness). The last thing I am going to do is put hidden feet on the board and elevate it about .375″, this creates some really cool shadows on whatever it rests on.


I hope this helps. You can use these techniques to make lots of interesting grids, I have another half dozen or so ideas from making this thing and oh so little time…


John

 Fog of War Board

25 comments on this post:

  1. John,

    Wicked cool! Great way to make sure the angles will fit the grid perfectly. I don’t see it in the pictures, but for the first two cuts that would have sticks hanging out to interfere with the fence and stop block, how did you make those cuts?

    Thanks,
    Rutager

  2. Rutager-

    The first time I made these I had a false fence system clamped to the JMP top. On this version, because I did not have many spare parts, I took the first two sides down on a stationary disk sander. I also neglected to mention that when cutting the small grids I switched over to the 32 TPI blade. Huge benefit and really efficient.
    -John

  3. You are welcome! The JMP can do amazing things once you realize work holding is the name of the game.
    -John

  4. John,

    Putting the stick grid on a base that is the same size as the space between the base grid is as simple as it is brillant, no matter where the sticks come out, they end up at the perfect angle to the grid walls; I could see making a “V” cut in a base plate could allow for cutting all four sides even with the sticks hanging out.

    The chess board is impressive; I remember seeing it on the first day of class and wanting to make it even more than the pieces! Although making the pieces pushed my JMP skills upward several notches.

    -Rutager

  5. Thanks for this, John. A very impressive photo essay of incredibly precise joinery. I love your solutions to the various problems you encountered (or anticipated). But that’s a big part of the fun of woodworking, isn’t it? I lie awake at night, coming up with solutions to interesting cuts, the order of operations, the tools I’ll use, or nonlinear ways of approaching a problem. Woodworking becomes a very pleasant extension of my science, which fundamentally is really not that different in the application of creativity and synthesis of tools, knowledge and approaches.

    As for using skids to get properly-thicknessed pieces, I wait in breathless anticipation for my CT-18! I have a growing list of projects that will benefit from those depth skids!

    Thank you so much for sharing your amazing knowledge and creativity with us. Those poor non-DSN members just don’t know what they’re missing!

    — Peter

  6. I wish I had the CT-18 for this job! I used wood skids attached via DS tape for the board bones.

    I think I should write something on how to REALLY use digital calipers as I believe most folks under utilize the potential. Now to find the time…

    BTW, there is light at the end of the CT-18 tunnel!

    -John

  7. Rutager,

    Those pads were not exactly the opening size, but close. I wanted to see the cuts as they occurred and not score the pad as well. FYI.

    John

  8. John,
    I hadn’t heard of gage pins before this and went looking on the web at them. I see they come in sets of plus and minus. What the difference and why use one over the other?
    Thanks
    P

  9. Paul,

    A very common use for precision gage pins is for measuring hole diameters, and as such the minus set provides about 0.0002″ clearance. The same can be said for the plus set. So, if you have a hole with a plus or minus tolerance spec, you can quantify with both sets.

    Now this is going to sound strange coming from me, but in woodworking, buy the least expensive gage pins you can find. I own pins gages from .001″ thru .750″ by 0.001″ increments and spent less than $150. These very pins would get me fired in an aerospace machine shop, but my work doesn’t leave the ground.

    They are indispensable for; holes, grooves, spacers, and measuring all sorts of gaps. I really like them for setting the depth skid “gap” on my planes. You set the plane up to cut silky shavings, set your skids to make a test cut, cut until the plane quits cutting and measure. You will be off your intent most likely, but now you know what pins to use. BTW, the pins will vary by 0.001″ at the nose and rear of the sole but it will not matter.

    Does this help?

    John

  10. Yep..
    Thanks
    Bogles the mind we humans can make machines that make other things of such precision. We’re a fascinating species.

  11. Ironically, gage pins are rather crude compared to other methods. That makes us even more interesting as a species.

  12. John,
    I am wondering if you needed to pay attention to the grain orientation when thicknessing the lattice strips. It seems to me that if the grain were
    oriented in the “bad” direction that causes tear out, the blade of the plane would tend to pull the strip up towards the bottom surface of the plane, resulting in the piece being planed too thin. It seems like it could end up quite thin with repeated passes that catch the badly oriented
    grain.

  13. Don-
    Grain direction absolutely matters, but it is not a big deal. The stock was about 0.010″ oversize and my plane was set up to take about 0.0015″ passes. You KNOW on the first pass if the stick is backward. rotate it, clean up the “bad” pass, flip 180 degrees and plane away until the skids hit.

    -John

  14. John,

    Digital calipers and gauge pins; tools that aren’t normally associated with wood working, do you have any more that you would recommend for our shops?

    Thanks,
    Rutager

  15. John,

    If you can’t get this tool making gig to pay off, any thoughts about getting the contract to make stir sticks for Starbucks?

    -Rutager

  16. “Rutager get back to work,” is what you’ll be yelling if you make the mistake of hiring me at your stir stick factory- on the plus side, I do have my own tools.

    John,

    In the picture of the planing board, I can’t tell, but is that a melamine board with a groove in it or some other thin material applied to a board?

    Thanks,
    Rutager

  17. Gentlemen, Rutager, Dennis,

    For those of you that care, please stay tuned. For those of you that do not either ignore this completely or turn your radio down. I will be coming to the BCTW 30th Gala. Arriving Wednesday and leaving Sunday. :o I am sorry to inflict myself upon you all but really, how could I miss this?

    You may now turn your radio back on or up. :o

    Fred

  18. Fred-

    That’s good news! Please leave your Entertainment Center in PA…. it would fit right in out here in Birkenstock Country.

    -John

  19. John,

    I am sorry but the EC has already been shipped and will arrive at BCTW next week. Oh, and I have hired a marching band to coincide with it’s arrival. :o

    Fred

  20. John: I am good and properly jealous of the people going. Best of luck on the exhibit!

    I’m making up my mind on WIA in November and noted BCTW isn’t (yet?) listed as an exhibitor. While my hands would probably be safer, you’d certainly be missed.

    Dave

  21. John,

    For the thicknessing jig, did you just cut a groove in some melamine or did you stick some melamine on top of a board to create the groove? And is there DS tape stopping the pieces being planed from moving? Thanks.
    Kevin

  22. Kevin,

    I just cut a groove in the melamine. To keep the parts from moving I super glued a small stop, it will get planed to thickness on the first piece and is net thereafter.

    John

Leave a Reply